Carrier

• Series 60 Detroit engine
• Allison CLT5 8-60-DB transmission
• Positive air shut off (located at drillers and sand line controls)
• Tn-drive rear axels (2-20,000lbs front axles with ABS brakes, 3- 44,000lbs
• Rear axles tn-drive/air ride)
• Rykar RK450 drawworks, 42x10 main drum, 38x8 sandline drum
• 40” Kobelt disc brake
• 2-winch lines
• Elevated operators pad
• 1200 feet or 1 inch drill line, 12,000 feet of ‘/2” swedged sand line
• Crown saver tied into brake system
• Ram saver tied into driller’s controls
• Electronic sand line depthometer
• Rig floor with fold out wing, comes with one extendable aluminum stairs
• Lock out box
• Pull bars at front and back for towing
• This unit was designed to meet all new load secure requirements for Alberta Highway Department

Derrick

• 104’ derrick 220,000 lbs hook load
• Emergency escape system for monkey board designed with escape buggy
• Line from back of monkey board to ground
• 2 self retracting lifelines (davit arm with retracting line for derrick hand on
• Monkey board and rod basket)
• Adjustable/removable monkey board fingers
• Rod basket
• 100 ton 73A load traveling block
• Incandescent lights

BOP System
• Class 111-40 gallon Rykar accumulator (5-60 gal pre-charge bottles with 2
nitrogen back-up bottles)
• Townsend 7 1/16 5000 psi double gate
• Schaffer Spherical 7 1/16 5000 annular
• Kill Spool with 5,000psi gate valve, tapped and bored for
2000/3000/5000psi weliheads
• 6—10 m fire proof hoses coming off remote controls
• Ram saver
• Control stand (remote control designed with easy access doors over
controls)

Pump (mobile)
• Series 60 Detroit Engine
• Allison 750 DB transmission
• Oilwell SA-640-5 rig pump
• Positive air shut down
• 5,000psi 7 valve manifold, pop valve and check valve
• 3x4 Mission charge pump with hydraulic motor
• Pre-fab around controls and manifold
• Back up beepers
• Cowl muffler
• 4” suction screen
• 2-4” suction hoses
• 2-2” 5,000psi kelly hoses
• 2 halogen lights for night operations
• Center roll for ease of unloading
• 30,000 lb winch
• Lock out box
• Oiler for pump packing
• Tire chains
• Pull bars at front and back for towing
• Rykar Industries 4 axle carrier
• This unit was designed to meet all new load secure requirements for Alberta Highway Department

Tank
• 31 m3 2 compartment tank
• Front and back 3” suck out line with 8” sunken floor (used by tank trucks to
suck tank dry)
• Front stairs, ladder on rear of Tank
•Manlift
• Poor boy degasser
• Mix hopper
• 2” 5000 psi line pipe
• 2” heater coil
• Ground block at front and back
• Racks for 2-4” suction hoses
• Racks for 2-2” Kelly hoses
• 3 section fluid trough
• 2 mud guns
• Wind socks
• 4’ florescent light
• This unit was designed to meet all new load secure requirements for Alberta Highway Department

Doghouse
• 8 x 32, 2 compartment building pulled by pintle hitch
• 40 KW Isuzu Generator
• 220-3 Phase Electrical Panel
• Bathroom facilities

Bed Truck
• 2006 Freightliner FLD 1 2OSD
• Allison 4500 RDS Automatic transmission
• Series 60 Detroit engine
• Tn-drive 46,000lbs rear axels, full lock up axles
• 60,000lbs Tulsa winch package
• Texas bed with kick up center roll for easy and safe unloading
• Positive air shut down
• This unit hauls junk box, 8x1 6 base mat for rig and tows doghouse.
• This unit was designed to meet all new load secure requirements for Alberta Highway Department.
• This is a full size Texas Bed Truck capable of bed hauling boilers, power swivels, 400 bbl tanks, and 5th wheel trailers

Utility Skid
• 5000psi test stump
• Tong swing out arm for safe rig inlrig out of tongs
• Upright tool box with baskets above and below
• This unit was designed to meet all new load secure requirements for Alberta Highway Department.
Handling Equipment
• Gill Model 500 tubing tong with air back up and hydraulic lift arm,
60.3mm 73mm and 89mm jaws
• Cavins Model C 100 ton air slips
• Big D 60.3mm 73mm elevators (100 ton)
• Rod equipment for 5/8” to 1” rods
• 72” 150 ton bales

Extra Equipment
• Mud can with 3” out let
• Mechanical pack off, 60.3mm 73.0 mm and 89.0 mm rubbers
• Low line slips (Mission) 60.3 mm and 73.0 mm inserts
• 73.0 mm sour service 5,000psi master valve
• 2-8’x40’ mats, 1-8’x 16’ tubing mat
• Catwalk and 2 sets of pipe racks
• 2-73.0 mm stabbing valves
• 80 HP boiler with two steam heaters and 1’ return line
• Corband sprayer installed in swab tree for sour fluid swabbing
(this safety feature eliminates workers standing on draw works applying
corban with scrub brush or sprayers)
• 2 pipe tubs

Trailer
• 22 ft. Trailer c/w 2- 7,000lb. axles
• Space also available on deck for hauling pipe etc.